Parker NDT Accessories
“A” Kit
- Steel carrying case
- 1 lb. Red Powder
- 1 lb. Gray Powder
- PB-1 Applicator
“A/B” Kit
- 1 lb. Red Powder
- 1 lb. Gray Powder
- PB-1 Applicator
- EA-140 Hand-Held UV Light
- 778A (16 oz.) Aerosol Can
- Fluorescent Particles
“P/L-A” Kit
- Super tuff plastic carrying case
- 1 lb. Red Powder
- 1 lb. Gray Powder
- PB-1 Applicator
“PL-A/B” Kit
- Super tuff plastic carrying case
- 1 lb. Red Powder
- 1 lb. Gray Powder
- PB-1 Applicator
- EA-140 Hand-Held UV Light
- 778A (16 oz.) Aerosol Can
- Fluorescent Particles
DC-300 DC Power Supply
The DC-300 DC Power Supply for the B-100 and B-300 Contour Probes contains an electronic circuit board assembly completely sealed within the housing. The 115 VAC Probe should be connected to the output power cord, while the input plug of the power supply should be connected to a grounded power source.
KS-100C Ketos Test Ring AS 5282 Certified
MG-01 Field Flux Strip (Burma Castrol) Type I (G)eneral.
MG-10S Centrifuge Tube Stand.
Can be used with all types of centrifuge tubes.
100ml Centrifuge Tube – Not Certified.
Stand available separately.
W-FI-10 Guass Meter
Intended to be used for Demagnetization and are calibrated during manufacture in a Homogeneous Field (Helmholtz Coil +/- 10 Gauss)
W-Fi-20 Guass Meter
Intended to check residual fields on small parts, and are calibrated during manufacture for a Homogeneous Field (Helmholtz Coil +/- 20 Gauss)
W-Fi-50 Guass Meter
Intended to check residual fields on heavy parts, and calibrated during manufacture for a Homogeneous Field (Helmholtz Coil +/- 50 Gauss).
Intended to be used for Demagnetization and are calibrated during manufacture in a Homogeneous Field (Helmholtz Coil +/- 10 Gauss)
W-Fi-20 Guass Meter
Intended to check residual fields on small parts, and are calibrated during manufacture for a Homogeneous Field (Helmholtz Coil +/- 20 Gauss)
W-Fi-50 Guass Meter
Intended to check residual fields on heavy parts, and calibrated during manufacture for a Homogeneous Field (Helmholtz Coil +/- 50 Gauss).
Pie Gauge
NA-16 Notch Defect Test Bar
NA-16 Notch Defect Test Bar, able to detect the smallest rejectable surface defects.
Complies with requirements of MIL-STD-271E and F (Ships), paragraph 4.3.1.2, and NAVSEA-TB-T9074-AS-GIB-010/271.
PB-1 Powder Blower
The PB-1 Hand-held Controlled Magnetic Powder Blower provides reliable and controlled application of magnetic inspection powder to areas previously inaccessible – horizontal, vertical and overhead.
PM-50 Permanent Magnetic Yoke
PM-50 Permanent Magnetic Yoke Set for magnetic particle inspection applications per specifications.
Available separately, or as part of a complete PM-50A Permanent Magnet Yoke Kit, which includes a carrying case, PB-1 Powder Applicator, and powder.
PM-50A Permanent Magnetic Yoke Kit
- PM-50 Permanent Magnetic Yoke Set
- Plastic carrying case
- PB-1 Powder Applicator
- 1 lb. Red Dry Magnetic Inspection Powder
- 1 lb. Gray Dry Magnetic Inspection Powder
W-PB-4 Powder Bulb
10 lb. Weight
TB-10SP
TB-10SP Special Magnetic Weight Lift/Defect Test Bar.
For 10 lb AC weight lift calibration of Magnetic Particle Inspection Yokes. Plus the reverse side contains artificial defects.